All posts by SubComon

Building a Barn Door

unique barn doorYesterday Todd, my second oldest brother, wanted to make a sliding barn door but then he complained that it would take too long, too expensive, and too hard. It was a long talk, but I was able to convince him that everything he knew about barn doors was a lie. Building a farm door only takes seven hours to get done professionally and two if you are fooling this article. Everything that used here only cost 378 dollars and if I can make / create a barn door, then anyone else can. Now here is how you do this in the simplest of terms:

1. Join the Boards
One of the hardest things about starting out is knowing your dimensions. We are going to assume that you already know the width and height of the door you want to build. Whatever your dimensions make sure to cut it half an inch shorter, gang the boards side by side, and finally screw the blocks in place. Remember to remove the clamps.

2. Combine Filler Strips
This self-explanatory and you should follow your cut list. After that only add adhesive to the lower stiles/rail. Make sure to leave a 1-inch channel for the track to guide the door later.

3. Slice the Chevrons
Now set your mitre saw to 45 degrees and cut off one end of each pallet board. Next use a combination square to mark the boards around one-eighth of an inch. Lastly dry fit them together, one chevron at a time.

4. Part the Corners
Just cut the corners of boards. Make sure to make all of the corners sharp to the touch.

5. Establish the Pattern
Dry fit the chevrons to both panels and lift one board at a time to apply more adhesive to the undersides. Press back to in place and repeat this process until you see the pattern appear.

6. Drill Hollow Holes
Your cut list should explain where you should drill the pocket holes. Typically you will drill two at each end of your upper and middle rails.

7. Build the Support
Now that you have everything ready, this should be as manageable as making a wood jigsaw piece. Just make sure to clamp the frame together once done.

8. Connect the Face Frame
Apply adhesive in a zigzag pattern along the filler strips. Align it with all four edges then you are done. Some people tack it down with brads every eight inches.

9. Rub On the Termination
No need to explain this. Barely sand the entire door and apply the finish.

10. Ascribe the Rollers
Mark the screw locations as indicated by your cut list then replace the wheels. Once you slip the wheels on the grooves, then do one final measure of the door and the track to determine how high the casing has to be.

11. Attach the Mounting Lumber
Use a stud finder to locate the framing and mark the locations of the casing. The hardest part is levelling the mounting board.

12. Fix the Track
If you’ve done it this far, then install the track should be a snap, however, this is unique depending on your measurements. Just make sure to ratchet the rest of the legs in place and snug them all up.

13. Scroll the Door On
Now just roll your creation in place and marvel at your work. Just make sure to position the door handle on the centerline of the stile then you have done it!

Related: http://www.knrslidingdoors.com/sliding-barn-doors/

Fix sliding closet doors on your own in no time

Custom sliding doorYour problem: It has been more than 10 years since we have installed sliding closet doors everywhere in our house. Everything was fascinating and worked well until recently when suddenly almost every sliding door in the house started either to come off tracks or get jammed against each other. No matter what we tried to do, the situation is only getting worse.

Handyman’s solution to your problem: every day your handyman’s office receives a multitude of calls with similar complaints. The majority is about custom sliding closet doors that came off track and it is impossible either to get them back on track or even move. Once there was a case with a trapped person inside a closet door who finally managed to get out but the door still was not functioning right. Therefore, do not feel alone with the problem, we are about to give you some invaluable tips on how to handle came off track custom sliding closet doors.

According to KNR Sliding Doors Culver City, there are older style doors, which are a bit different from the modern ones. First, let’s see how to come with the older ones and then move to those a bit more up-to-date. The first type is sliding doors is characterized by ceiling mounted tracks that do all the support for rollers. The later as a rule go in the shape of an open hanging “j” and that is the reason why the doors tend to come off track in case they are pushed aside or vertically instead of pulling them horizontally from one side to another.

Occasionally, custom sliding closet doors can stuck because of something inside it. In this case, it is a bad idea to push the doors in different directions and trying to lift them. The only thing you will achieve is that the rollers will simply come off track and it will become harder to repair the doors. Especially if your sliding closet doors are those heavy ones.

Sometimes there is the problem with original sliding doors that are put over hard wood floors. The problem here is that the carpeting was put on the floors later than the doors were installed. As a result, the height of the carpeting is not counted into the construction that causes more troubles when opening the sliding closet doors. A good way out here is to remove the doors and trim the base. Such a step will allow you to get everything back on track and enjoy your doors for more years to come.

If your only problem is relatively old rollers, then you have a chance to replace them with the new ones. However, keep in mind that it will be necessary to do the same with the entire track mechanism. Only in this case, you will achieve the goal and your sliding closet will move along as if they are new. By the way, such custom mechanisms are available in all hardware stores, you just need to know the right measurements of your custom sliding closet doors.

When talking about the new generation of mechanisms for custom sliding closet doors,  the situation is more simple. Once you install the rollers, trolley and new “C” shaped track correctly, you will not have any additional problems with this type of sliding doors.

The above-mentioned option of replacing the old mechanism with the new one seems logical only when the doors and the frame are is good condition. Then, to do the job on a standard door will take about 2-3 hours. By no means, it will make your life easier and you will not get angry every morning because our closed doors have jammed once again.

The same renovation approach can be applied to pocket doors but in this case, it will be more time-, effort- and material-consuming. The reason is quite obvious as usually pocket doors have a more complicated construction and it is not that easy to get access to the mechanism and replace it with a new one. Note that sometimes it is hard to replace the track as the process requires a 1-2 square foot opening in a drywall to get the things done from the inside. If the drywall is removed, the task gets more simple but not in case if the cabinets of the pocket doors are tiled. The way out here is to move the cabinets for some time or create an opening in the tile.

Source: http://knrslidingdoors.com

Can Adults Wear Braces?

The rise in technological advancements and Orthodontic research have led to the production of less bulky, inexpensive, and much more aesthetically appealing adult braces. This has resulted in an increase in the number of adults wearing braces nowadays. Adults that are self-conscious about their smile, irrespective of the age, are now getting braces to correct their dental alignment and eventually improve their smile.

Adult braces are specially designed for anyone above 18years of age. Nowadays, common orthodontic issues including misaligned teeth, crowded teeth, bite problems, and jaw disorders can be easily corrected using braces. However, if left unattended, such problems can eventually result in headaches and earaches, tooth decay, gum disease, and also chewing, biting or speaking problems.

adult braces
Adult Braces

Now more than ever, adults understand how much their smile contribute in the way that they perceive themselves, their self-esteem and how much well-aligned teeth play a part in their overall health, this has led to more and more adults seeking orthodontic treatment to perfect their smiles and improve their health. On the other hand, dentists are recommending adults to put on braces to improve their “orofacial” appearance.

 Determining the ideal braces to wear

Adult braces are made of different materials and they come in different types and sizes. For this reason, it is always important to visit an orthodontist in order to get the right brace prescription.  The orthodontist will examine your teeth and jaws and recommend the best fitting to wear based on your particular problem. Through the advice of the adult braces San Diego dentist, you will be able to get the most suitable adult brace for your teeth.

How long will you have to wear braces?

The duration of wearing your braces will depend on your treatment plan. Typically, the more complex your teeth condition is, and the older you are, the longer the treatment period. Most adults can count on wearing full braces within 12 and 24 months, then afterwards wearing a retainer to position and align tissues around the straightened teeth.

 Will treatment be uncomfortable?

At every visit to your adult braces San Diego dentist, the interconnecting wires are tightened, exerting mild pressure on the brackets to shift your teeth or jaws gradually into the ideal position. Your teeth and jaws may feel slightly sore, but the discomfort is only for a short period. There are other chances that some of your teeth may need to be removed to create space for teeth being moved with braces and for appropriate jaw alignment.  If you are recommended to wear aligners, you may experience some soreness while your mouth adjusts to every new plastic tray. So, other than the minor soreness, the rest of the treatment will be comfortable.

Home care of your teeth with braces

To ensure that you maintain high standards of oral hygiene, you should brush after every meal using a soft-bristled toothbrush and fluoride toothpaste to avoid enamel staining around brackets.  Using a floss threader, take your time to floss between braces and under the wires. Last but not least make sure that your teeth are cleaned every six months to keep them healthy.

Click for more about San Diego Dental Services

Helpful Mold Removal Tips

These spores float around in air create their way straight in to the home. The safest way to treat molds is actually assume oftentimes deadly you. These areas include bathroom fixtures and moldy walls.
No one really wants to have a home filled with mold. In fact, owning a home that contains mold is very hazardous. Mold can cause numerous health threats for you and your loved ones.

Begin by removing any visible mold or mildew. This must be done outside, so mold spores aren’t released in to your home. Possess a bag, or multiple bags available to deposit removed mold interested in. The mold only need to brush off or remove easily. May doesn’t go easily could be removed in the cleaning solution.

Organic websites tout Non-Toxic Mold Cleaner Molderizer to be a fantastic organic mold removers. This product is expensive, though, like other organic products. One jug in the mold remover costs almost sixty dollars, so for are on a tight budget you might call for to go else. But if the price isn’t an issue, then this is one of the many best organic, professional strength mold removers.

Non-Toxic Mold Cleaner Molderizer is generally consider a great organic choice for a mold remover. Definitely not enough . is expensive, though, like other organic products. One jug these mold remover costs almost sixty dollars, so if you are on a great budget you may need to get another thing. If, however, you don’t mind the price and here are a few commercial strength and organic mold remover, this may be the best product that you can buy.

So is black mold removal necessary? Well, considering the army developed these weapons to kill people, an individual want these toxins in your house? The truth is these are not the only household molds that makes people vomit.

Having identically meaning, “Mold”, “Toxic Mold”, and “Black Toxic Mold” are all phrases constructed by the media. Primary unique thing topic will be the type of species that exist in a sample of black mold. You can find a good idea about how toxic or problematic the mold is skilled the connected with the kinds.

Ultimately this fungus is often a tough thing to need to face when present up in your home, but getting associated with it once you first can is certainly important step that always be ready consider. Check your house for any signs of your mold after which it get associated with it should you can using the proper precautionary steps for elimination.
Mold spores could one of this allergen that causes migraine and headache during these people. Take into account the actual cost and reputation of each product that you’re researching.